/diy/ - Do It Yourself

The weighted part is the clear upside down Gatorade bottle. I can add rocks & water to fine tune the ram pump.

I did the wood and wire, because I didn't want to glue the (PVC 2" 3/4 reducer) top on so I can adjust if I have to. I'm about to go install it. I have a headlamp now. :-)

Also, I have a girlfriend now. Keep seething, incels.

My girlfriend.

>>1703347
wewlad..

what is this thread?

>>1703347
Nightmare fuel.

TODAY

LIKE EVERY OTHER DAY

I MADE

A HUGE MISTAKE

>>1703361
what have you done now?

>>1703337
still cranking out these machined steel plate parts, but faster this time because I have two pallets now.

>pallet1 in, run op1
>put pallet 2 in, swap out clamps on pallet1, run op1, wait
>take pallet2 out, put pallet 1 in, run op2
>take pallet1 out, put pallet 2 in, run op2
>swap new material in pallet2, wait
>take pallet2 out, put pallet1 in
>swap new material in pallet1, wait

er uh, something like that. pretty sure that's fucked up

>>1703337
>What did you make today?
A bowl of cereal and my bed. Can't win 'em all, champ.

>>1703337
A shitty wood box for a magnetic ballast.

Prefabricated trusses

A Box for my chisels.

Love

>>1703449
Post pictures

>>1703470
>Post pictures
Sure thing.

The wood is sapelle. I used scrap pieces left over from my recent tool chest project.
The box will fit in the middle level of my tool chest, below the hand tray, but above the "basement". The logo I printed on a laser printer, then transferred the toner by soaking through the paper with acetone and rubbing thoroughly with a credit card.

>>1703591
I cut the finger joints by hand, which is something new for me.The dowels are 1/8" bamboo.

>>1703592
The chisels are held by magnets.
I don't have a latch yet. I'm thinking about using magnets to latch it closed.

>>1703593
last one

>>1703591
>>1703592
>>1703593
>>1703596
Very cool. Thanks for sharing. How long have you been into woodworking?

>>1703610
>How long have you been into woodworking?
About 4-5 years, but I've been away from it for almost a year before I got started again in September.

Here's my tool chest project. The hand tray is done, but the chest itself still needs finishing.

>>1703625
>About 4-5 years, but I've been away from it for almost a year before I got started again in September.
Only 5 years? Damn. Good work man. Better than I could ever do w/ that much time and effort.

>>1703630
Don't hijack my thread asshole.

On a more important note... My waste valve is a really foot valve with the spring removed. I'm going to make a plunger out of a dowel. I just had a 3 hour nap. Getting back at it.

I'm still noodling on why the ram pump is not working like it was before, and that's because I disassembled that and it's a different system now. I guess that's the simple logic.

>>1703653
Maybe my pressure vessel is too small for the new pressure? OR my foam noodle inside the pressure vessel is kapoots? Or NOthing is wrong. Now that it's clear I'm hunting for a way to get it working. I also need to put pressure gage on the inlet to know what I'm working with.

This might work. Humm.

I made a confession. It’s not diy but I never realized how better it can make you feel. Telling you guys cuz this is the least shit flinging board

>>1703657
what did you confess anon?

>>1703593
mirin' your work

>>1703593
>>1703596
based

>>1703654
SHUT UP YOU STUPID FAGGOT

>>1703659
Inter family issues. Dr.phil/J Leno levels of crap. I’m pretty fucked up. I don’t wanna derail the board, but Anons, if you got shit holding you down, confiding in someone can really help

>>1703337
I made a bitch pregnant, help me br/o/s

>>1703657
>least shit flinging board
Depends, was your confession that you used a sharkbite or built a house out of OSB?

https://youtu.be/L94kmpyTykI

small updates to my utility truck camper.