/diy/ - Do It Yourself

use a spacer between them to take up the slack

or a stack of washers, piece of pipe, piece of wood whatever

>>1477562

@185 gallons/minute be done in like 3 days

fuck all other options

find a used one on kijiji

theyre stupid reliable too

dude buy a 2" honda trash pump thank me later

>>1474397

very carefully

also practice

theyre broke because its a shite design

why do you even need the springs

just use it without springs

how the fuck do you expect us to know the fitting type on the supply of your stove

could be all kinds of different shit

i would bring

3/8 gas female ---> 1/8 npt male adapter
3/8 gas female ---> 1/4 npt male adapter

3/8 gas female ---> 1/4 gas male
3/8 gas female ---> 1/8 gas male

3/8 gas female ---> 1/4 left hand gas female swivel

1/4 npt collar
1/8 npt collar

1/4 npt street elbow
1/8 npt street eblow

1/4 npt ---> 1/8 npt reducer

thread tape rated for gas not the white shit

2 of these wrenches:
15/16
7/8
13/16
9/16
11/16

one of these wrenches:
1
5/8
3/4
1/2

tape your joints up properly dont over tighten

use a lighter to check for leaks with bottle barely open

choke yourself then beat it like youre beatin a nigger off your sister

theyre all pretty good makita dewalt snap on milwaukee

snap ons overpriced as shit

dewalts okay

milwaukee is better than dewalt

makita is trash can

ryobi/bosch just kill yourself

a wire mesh square tube about 1 inch by 1 inch by 2 feet long

stack a bunch like idk 5 on top of each other and use this as the exit

set up camera to record

gas em out of whatever theyre in

record

play back at low speed and count

>>1467648

look out we got an oldfag here

>>1467711

i use a 1/2 inch milwaukee every day and its incredible how powerful they are

it will probably take them off with barely a grunt

still though op, cordless 4" grinder and a couple zipcuts

be done in 20 mins

best way to fix a kicked in door is to move out

>>1468071

the tapes there to keep the socket sliding on the ready rods noise down so he doesnt wake his mom up

>>1466417

also, not lug nuts no

but other bolts, yea

dissimilar metals for sure, like aluminum with a steel bolt, transmission filters etc that are all corroded

if you dont know what to feel for youll pull the bolts right out before your chinkerton even thinks of clicking

>>1466421

wat

if youre using any kind of metal youll be fine

like did you use a regular bolt

all it takes is one crafty nigger with a crescent wrench

i would just use a piece of shit so when (not if but when) it gets stolen who cares they did you a favor

>>1466831

good choice and good luck

bleach and ammonia 30/70 mix works incredible for removing rust

wont take out the pitting obviously but the rust will disappear before your eyes

go buy one, jamal

>>1466265

pressure inside diff > pressure of some other shit hes driving through

itll be fine

wtf are they for

>>1465795

the actual reason to torque your lugnuts is because over tightening will stretch the stud, distort the threads, and then wobble loose over time

if you do it every day, you probably have a good idea of the right torque and can get away without a torque wrench

if youve done it once, get the right shit so you dont kill your family

dont cheap out on torque wrenches, you might as well go by feel instead of a harbor freight

go with ultra pro, westward, blue point, snap on, etc

>>1465336

sorry but the metric system is for weirdos

Q drill

a third of an inch roughly

give it back, jamal